-
-
基本释义：
mating parts
配合件
英 [ˈmeɪtɪŋ pɑːts]
美 [ˈmeɪtɪŋ pɑːrts]
词典扩展 短语搭配 权威例句
词组短语
1. Mating Parts Number 配合零件料号
2. fit-rate of mating-parts 孔轴配合率
3. drilled together with mating parts 与配合件同时钻孔
权威例句
1. To have an interference or force fit between mating parts, the tolerances must be such as to create a zero or negative allowance.
为了使配合零件之间具有过盈或强制配合，公差必须产生零或负允差。
2. A New Method for Assuring the Balance of Mating Parts in Selective Assembly
一种保证分组装配零件数量均衡的新方案
3. In mass production, where mating parts must be interchangeable, unilateral tolerances are customary.
大规模生产中配合零件必须能互换，单向公差是经常遇到的。
4. All mating threaded parts are made of dissimilar, non-galling metals.
所有的螺纹配合件均采用不同的材质以避免互相咬死。
5. Hexagon thin nuts are also called Hexagon jam nuts. They are often used when there is spacial limitation on the mating parts.
六角薄螺母的厚度较薄，多用于被连接机件的表面空间受限制的场合。
6. Secondly, it is used as a method of obtaining very close fits between mating parts such as pistons and cylinders.
其次，它能用作获得像活塞与气缸之类配件间过盈配合的方法。
7. An allowed difference in dimension of closely mating machine parts. "Copper alloy integrated shaft sleeves for plain bearings with gears& Types, dimensions and tolerances"
公差，容差机器配件的公差，容差GB/T2510-1981滑动轴承铜合金带挡边整体轴套形式、尺寸与公差
8. All mating threaded parts are made of dissimilar, non - galling metals.
所有的螺纹配合件均采用不同的材质以避免互相咬死。
9. Fits can range from free running or sliding, where a certain amount of clearance, exists between mating parts, to press or interference fits where parts are forced together under pressure.
配合可分为结合件间有自由转动或滑动从而需要具有一定间隙量的间隙配合以及结合件需要紧密压靠一起 的压配合或过盈配合。
10. The heat-transfer effects between the mating parts and the fluids including the sealed fluid and air were studied.
对机械密封与试验介质间和大气间的传热效应作了一定深度的研究。
11. Experimental Research on the Life Time of the Valve Mating Parts of the Main Pump of Shearers
采煤机主泵配油副寿命的试验研究
12. Mating arithmetic of parts is to resolve the problem of automatic assembly.
零件配合算法研究零件之间的自动装配问题。
13. The study of mating parts material of hydraulic piston pump
液压泵双金属摩擦副材料的研究
14. It is the minimum clearance space intended between mating parts and represents the condition of tightest permissible fit.
它是配合零件之间最小的预期间隙空间，代表着允许的最紧配合条件。
15. On suitable fitting of centering surfaces between mating spline parts in agricultural machinery an investigation of efficiency characteristic of typical circuits of agricultural machinery hydraulic systems
关于农机用花键定心面的合理配合精度农机液压系统典型回路的效率特性分析
16. Fretting damage exists on tightly mating parts at large, which is one of the disaster reason making components and parts fail.
微动损伤普遍存在于紧密配合部件中，是造成零部件失效的主要祸患之一。
17. To have an interference or force fit between mating parts, the tolerances must be such as to create a zero or negative allowance.
为了使配合零件之间具有过盈或强制配合，公差必须产生零或负允差。
18. Secondly, it is used as a method of obtaining very close fits between mating parts such as pistons and cylinders.
其次，它能用作获得像活塞与气缸之类配件间过盈配合的方法。
19. When mating with other parts, this melt filter can be used not only in PET melt but also in the filter of o...
与其他部件配套后，不仅用于聚酯熔体，还可为其他高黏液体过滤。
20. Several Key Problems on the Assembly of Mating Parts with Robots
互配零件机器人装配作业的几个关键问题
21. Thermal spray coatings for resistance to fretting at interface of mating parts can decrease fretting damage in effect. The coating has the advantage of good effect and low cost, so it has been studied and applied widely.
采用热喷涂技术，在配合件接触面喷涂抗微动损伤涂层，能有效地降低微动损伤，具有抗损伤效果好、经济效益显著等特点，得到了较广泛的研究与应用。
22. According to the requirements of appli-cation and processibility of the splines with hard broached holes the authors sug-gest suitable fitting of centering surface between mating spline parts for different construction and working conditions.
文章从使用要求和工艺可能性等条件出发，分别对不同的结构和工作条件提出花键定心面配合的精度要求和结构设计措施。
23. Proper torquing avoids elastic separation of the mating parts under load and resists gradual loosening over time.
扭矩正确，就能防止配合部件在负荷作用下出现弹性分离，并防止部件在长期运转过程中逐渐松动。
24. Allowance , An intentional difference in sizes of two mating parts.
两个配件之间的预留的尺寸差.《互联网》
25. Does the supplier understand the critical nature of dimensions that interface with the customer's application of their mating parts?
供应商是否理解其与其它件相配合的关键尺寸对顾客使用的影响？
26. The cross-sectional area of the flow path between mating parts of the traditional 60 ° or 90 ° conical angle needle valve of fuel injector is decreasing towards the interior side. This feature limits the fuel discharge per stroke.
众所周知，传统的喷油器的针阀锥角为60°或90°，它的阀座流道的流通面积向下逐渐减小，这就限制了每循环喷油量。
27. The Effect of Determinating Tolerance and Mating of Machine Parts on Their Cost
选定公差与配合对机件加工成本的影响
28. Workshop oriented numerical method for improving the fit rate of accurate mating parts
面向车间提高精密孔轴配合率的数字化方法
29. In mass production, where mating parts must be interchangeable, unilateral tolerances are customary.
在大规模生产中, 要求互相配合的零件时可互换的, 因此单向公差更合适.《互联网》
30. Fretting damage exists on tightly mating parts at large, which is one of the disaster reason making components and parts fail.
微动损伤普遍存在于紧密配合部件中，是造成零部件失效的主要祸患之一。
31. The sum of the parts of the mating parts is less than or equal to the allowable deviation of the assembly.
相互配合零件公差之和小于或等于装配允许偏差，零件完全互换。
32. When mating with other parts, this melt filter can be used not only in PET melt but also in the...
与其他部件配套后，不仅用于聚酯熔体，还可为其他高黏液体过滤。
33. Tolerances for press fits can become very critical because parts can be easily damaged by attempting to press fit them if there is an excessive difference in their mating dimensions.
对于压配合来说，对公差极为挑剔，因为如果结合件的配合尺寸相差过大的的话，那么在试图强行压配到 一块时极易将其损坏。
34. With the bilateral system, this is not possible without also changing the nominal size dimension of one or both of the two mating parts.
而在双边系统中，不改变两个匹配零件的一个或两个正常值的话是不可能的。
35. New Mode of Lean Production for Precise Mating Parts
一种实现精密配合零件精益制造的新模式
阅读全文
下载本文